From MLCCs to Optical Chips: China's Production Gains Leave Upstream Gaps
For international buyers assessing Chinese electronic components, production capability and supply-chain localization are separate questions. Miniature MLCCs, advanced package substrates and 100G EML chips now have concrete production disclosures. Following those products upstream, or into the next generation, reveals continuing material purchases, manufacturing challenges and customer qualification.
The relevant unit of analysis is a product operating under defined conditions. The examples below span capacitors, packaging materials, automotive control, optical chips and inertial sensors, with commercial stages kept distinct.
MLCC production does not complete material qualification
High-end MLCC development follows several paths: smaller footprints, higher capacitance at a specified size and voltage, and automotive temperature, mechanical and lifetime requirements. These attributes may coexist but are not interchangeable.
Weirong's June 2026 exhibition material lists 0402-size 22 μF, 4 V and 0805-size 100 μF, 2.5 V products for applications including computing equipment. Such low-voltage capacitors support decoupling and filtering near processor supplies. The company also disclosed production progress in 008004 and 01005 miniature families.
TDK's September 2026 CNA6P1X7R2A106K250AE introduction addresses a different task: 3225 metric size, 100 V, 10 μF, X7R and low-resistance soft termination for applications including 48 V lines. Production was scheduled to begin that month. Its voltage and mechanical requirements differ from a 2.5 V high-capacitance device.
Engineers must compare effective capacitance under working voltage, impedance versus frequency and temperature behaviour. Class II ceramics exhibit DC-bias effects, so nominal capacitance is not the continuously available value under all operating conditions.
Thinner dielectric layers and more layers demand stable powders, metal pastes, cast films and firing processes. Weirong's September 2026 prospectus says overseas suppliers accounted for 39.48% of first-half purchasing expenditure on the relevant raw-material categories, including paste, ceramic powder and PET film. This is one company's procurement measure, not an industry import-dependence ratio.
Sinocera's interim report describes continued development and customer validation of dielectric powders for AI-server and automotive MLCCs, high-capacitance pastes developed with customers, and completion of some capacity expansion. Material supply already has a base; new formulations still require qualification within the customer's device and process.

Figure 1. Original Chinese-language excerpt from Sinocera's 2026 interim report covering dielectric powders, high-capacitance pastes and customer validation.
Replacing a material supplier also changes a production relationship. Powder and paste compatibility, firing conditions, terminations and inspection need reassessment. Procurement savings must be weighed against validation, process-adjustment and quality-control costs. Repeatable results on customer lines establish durable adoption.
Package-substrate production and upstream material supply are different capabilities
High-speed chip connections require package substrates and PCBs whose dielectric loss, processing precision and structural stability work together. Ajinomoto's ABF is an interlayer insulating film within a package substrate, not the complete substrate itself. Its June 2026 material places the film between copper interconnect layers, beneath the chip and above the motherboard.

Figure 2. Ajinomoto's June 2026 manufacturer slide. Yellow identifies ABF insulation; chip, package substrate and motherboard occupy different levels.
Shennan Circuits reported volume production of high-end FC-BGA products at multiple customers in the first half of 2026, supporting the Guangzhou factory ramp. This establishes progress beyond pilot production in some programmes. It does not establish domestic sourcing of every substrate film.
Ajinomoto describes working with customers from development to align performance and price, then using feedback and trial evaluations to reach production. New material suppliers similarly need experience linking formulation changes with process windows and qualification results.
Novoray's interim report says certification of liquid-phase spherical silica accelerated and its ultra-pure spherical silica project for extremely low-loss high-speed substrates entered industrialization. The stated application targets M9LVL-and-above substrates; M9 is not a universal silica-powder grade. The project's Df of no more than 0.0003 appears as a target, not a guaranteed volume-product specification.
Particle distribution and surface properties must suit the resin system, with loss verified in the actual composite. In November, Ajinomoto reported strong high-performance ABF sales for AI, servers and networking, and expected larger substrates and more layers to increase material usage. New entrants therefore face evolving requirements even while qualifying for existing programmes. Samples alone do not establish repeatable manufacture on customers' equipment.
Automotive drivers have shipment records while MCU software affects adoption cost
An automotive power stage, isolated driver and MCU each require their own evaluation. The driver transfers control across the voltage boundary and supports protection; the MCU handles control, communications and diagnostics. A SiC device's acceptance does not qualify the entire control chain.
NOVOSENSE's 2026 interim report says single- and dual-channel SiC-oriented isolated drivers were shipping at scale into automotive OBC and other markets. First-generation functional-safety drivers also had scale shipments; second-generation devices were undergoing sampling and testing with several project nominations. OBC supply does not establish traction-inverter adoption.
Its November exhibition material presented NSI6911F with drive, sensing and diagnostic integration. That product description and the interim report's generational shipment disclosures are separate evidence; together they do not establish that specific part's shipment scale.
Infineon's June 2026 1EDI3040AS and 1EDI3041AS announcements provide contemporary overseas comparisons. Both target automotive traction inverters using IGBTs or SiC MOSFETs, with multilevel slew-rate control and SPI configuration and diagnostics. The 1EDI3040AS additionally integrates a closed-loop flyback controller to adjust the high-voltage-side gate supply.
These functions affect switching behaviour and peripheral circuitry. Safety documentation, models, boards and configuration tools also determine engineering effort. Current ratings and isolation specifications are only part of the comparison: fault response, diagnostic coverage and support must fit the customer's system safety goals.

Figure 3. Infineon's April 2026 manufacturer architecture showing MCU, isolated drivers, supplies and power modules. The family also received a June announcement. This is not a specific vehicle customer's production BOM.
GigaDevice's September 2026 GD32A711/A712 manual lists Cortex-M7 processing and memory configurations. In August, it announced GD32A7 adaptation validation with Elektrobit EB tresos Classic AUTOSAR and opened applications for joint solutions and evaluation kits. This helps connect devices to established software workflows. Software migration, drivers, diagnostics and tests still cost engineering time; a cheaper chip need not lower total programme cost. Adaptation, vehicle nomination, production adoption and continued supply remain separate milestones.
Optical-module volume and laser-chip generations advance separately
Zhongji Innolight's interim report describes increasing 800G and 1.6T shipments, including volume growth of 1.6T silicon-photonics modules. Chinese module suppliers already participate in high-speed data-centre applications. Module aggregate rate, however, differs from individual optical-channel rate, and module deliveries do not identify every chip's origin.
Yuanjie Technology reported volume shipments of 100G PAM4 EMLs, customer validation of 200G PAM4 EMLs, and bulk delivery of 70 mW and 100 mW continuous-wave lasers. EMLs and CW sources used in silicon-photonics architectures perform different functions.
Lumentum's May 2026 fiscal-third-quarter material already reported actual 200G EML shipments. The disclosure dates differ, but they show different commercial stages for that generation. Yuanjie's 100G delivery record cannot substitute for 200G qualification.
EMLs combine a laser and electro-absorption modulator. Yuanjie identifies epitaxy across different regions and interface quality as technical issues, with material defects affecting reliability. Module integration adds driver, optical-packaging and thermal requirements. Performance distributions across batches continue to influence packaging/test efficiency after an individual sample meets its targets.
Chinese module expertise can bring local chips closer to application feedback. Stable procurement still depends on results in the specific module and manufacturing consistency.
Precision MEMS requires dynamic performance and calibration
Gyroscope performance extends beyond one static accuracy figure. Temperature, vibration, operating time, accumulated error and calibration determine suitability for sustained attitude estimation.
Xin Dong Lian Ke's interim report says industrial gyroscopes had entered production and broad sampling. Monolithic three-axis devices were still advancing tape-outs at multiple foundries and reliability optimization, while a functional-safety six-axis IMU remained in R&D. Greater integration brings additional fabrication, packaging and test work.
The company describes non-standard bulk-silicon MEMS processing: foundries supply basic process modules, while the designer develops compatible manufacturing solutions and completes packaging, testing and calibration. Customers then perform compensation and system integration. Comparisons need aligned bandwidth, temperature and vibration conditions, with typical values distinguished from guarantees. More evaluations can generate useful feedback, but recurring, consistent deliveries establish wider acceptance.
Higher-end supply must also withstand price and manufacturing pressure
Weirong disclosed first-half 2026 gross margins of 25.38% for consumer products, 26.56% for industrial products and 34.41% for automotive products. Automotive margin remained higher, yet customer cost-reduction demands and competition lowered key product prices faster than unit costs fell.

Figure 4. First-half 2026 figures from Weirong's September prospectus. Margins reflect product mix, customers, prices and costs; they are not technical rankings.
Manufacturing efficiency must support customer price reductions and new development. Capacity plans or certification alone cannot demonstrate a stable business. Shennan's first-half package-substrate revenue of RMB3.667 billion and 31.35% gross margin include multiple substrate types, so neither figure can be attributed entirely to FC-BGA.
China's progress is best followed through specific programmes: material formulations validated on customer lines, complete device test records, and better software and diagnostic support. Qualification should lead to consistent batches, repeat purchases and viable costs. Finished-product volume, next-generation validation and upstream localization can advance simultaneously without reaching the same stage.
Evidence reviewed through November 18, 2026. Production, validation and R&D status refer to the corresponding disclosure dates.



